NEWS
新闻资讯
行业动态
- 哪些因素导致线束接触不良
- 本站编辑:杭州企力电子有限公司发布日期：2020-01-04 20:48 浏览次数：
1、金属物体将线束压伤，导致电线速绝缘层破裂，蓄电池正负极引线接反，检修电路故障时,乱接都会直接引起电气设备的不正常工作；
2、电气设备在运行的过程中要是出现其短路以及过载的故障，这样都会有可能会直接引起其电线束的损坏；
3、电源电路中哪点搭铁其电线束就会直接烧到哪里，设备中烧坏的部分和完好的部位的交接处可以有效的认爲这个地方电线搭铁，要是电线束烧坏到某个电气设备的接线部位时，就说明这样的电气设备出现了故障；
4、当碰触或拉动该电气设备的有关插接器，当碰触到某个插接器的时候，设备的工作忽正常或者不正常，这样就说明其插接器出现了故障；
5、要是线路接触不良其故障经常会发生在插接器的内部，要是故障出现的时候，这样就会直接引起电气设备不能正常的进行工作，在判断的过程中，有效的接通这样的电气设备的电源。
1. The metal object will crush the wiring harness, cause the wire speed insulation layer to break, the battery positive and negative lead wire is connected in reverse, when overhauling the circuit fault, the disorderly connection will directly cause the electrical equipment abnormal work; 2, if the electrical equipment in the operation of the process of its short-circuit and overload failure, which may directly cause damage to its wiring harness; 3, the Power Circuit where the tie-in its wiring harness will burn directly to where, the connection between the burnt part of the equipment and the intact part can effectively be considered to be the place where the wires are wired. If the harness burns out to the wiring part of an electrical equipment, the electrical equipment is out of order; 4. When touching or pulling the relevant plug of the electrical equipment, when touching a plug, the operation of the equipment is abnormal or abnormal, which means that its plug connector is out of order; 5, if the line contact is not good its fault often occurs in the connector's internal, if the fault occurs, this will directly cause the electrical equipment can not work normally, in the judgment process, effectively power up such electrical equipment.
1. The metal object will crush the wiring harness, cause the wire speed insulation layer to break, the battery positive and negative lead wire is connected in reverse, when overhauling the circuit fault, the disorderly connection will directly cause the electrical equipment abnormal work; 2, if the electrical equipment in the operation of the process of its short-circuit and overload failure, which may directly cause damage to its wiring harness; 3, the Power Circuit where the tie-in its wiring harness will burn directly to where, the connection between the burnt part of the equipment and the intact part can effectively be considered to be the place where the wires are wired. If the harness burns out to the wiring part of an electrical equipment, the electrical equipment is out of order; 4. When touching or pulling the relevant plug of the electrical equipment, when touching a plug, the operation of the equipment is abnormal or abnormal, which means that its plug connector is out of order; 5, if the line contact is not good its fault often occurs in the connector's internal, if the fault occurs, this will directly cause the electrical equipment can not work normally, in the judgment process, effectively power up such electrical equipment.
Copyright © 2020-2023 版权所有：杭州企力电子有限公司 